11KW high power concrete floor deep drawing machine 1-2 cm Old Road Planer 300mm bridge 

planer, double motor Cold milling machine 

一、產品用途：

300型電動自動行走銑刨機是一款適用于混凝土地面多功能表面處理的路面機械，廣泛實用于橋面

鋪裝，橋面拉毛，錯臺調平、舊路面刨除，以及機場跑道、城市廣場、大型工廠，物流倉儲、車庫、停

車場等混凝土地面施工、作業中。?

Model 300 electric automatic walking milling machine is a special road surface machine 

which is suitable for multi-functional surface treatment of concrete ground. It is widely 

used in bridge deck pavement, bridge deck stretching, stagger table leveling, old road 

surface planing, and Airport runways, city squares, large-scale factories, logistics 

storage, garages, parking lots and other concrete ground construction, operations.?

二、產品參數

型號 ZXB300

主電機 11kw/380v

自行電機 1.5kw

一次銑刨寬度 300mm

一次銑刨深度(混凝土) 5-20mm

一次銑刨深度（瀝青） 5-30mm

工作速度 4m/min

外形尺寸 1380×730×1180mm

整機重量 306kg

保養指南

1、為了安全起見，在進行保養前，所有的保養由合格的機修工來進行。

2、機器放在平整的平面上進行保養。檢查銑刀時要防止機器翻倒。

3、每次操作前用肉眼檢查機器：所有緊固件是否擰緊？是否有零件明顯磨損或開裂？檢查軸承、檢查

個個防護罩是否蓋住，注意軸承加油，本機軸承不能缺油。

4、每次操作前，要檢查皮帶松緊度。新皮帶在運轉4小時后應該重新調整松緊度。有斷痕、嚴重磨損的

皮帶應立即調換新的。調整皮帶松緊度：調整發動機安裝底板下的兩根高度調整螺柱，通過改變電機輸

出軸和銑鼓中心軸的中心距離來控制皮帶的松緊度。保持適當?shù)钠删o度。

5、每次改變銑刀排列時，檢查銑刀軸和軸襯。如果軸上出現磨損的槽，就需要換新的。

Maintenance Guide 1. 

For safety reasons, all maintenance must be performed by a qualified mechanic before 

maintenance is performed. The machine must be maintained on a flat surface. The milling 

cutter must be checked to prevent the machine from tipping over. 3. Visually inspect the 

machine before each operation: Are All fasteners tightened? Are any parts visibly worn or 

cracked? Check the bearings, check whether the guard cover, pay attention to the bearing 

oil, the machine bearing can not be short of oil. Check the tightness of the belt before 

each operation. The new belt should be re-tightened after four hours of operation. The 

belt with broken marks and serious wear should be replaced immediately. ADJUST THE BELT 

TIGHTNESS: adjust the two height adjustment studs under the engine mounting base plate, 

control the belt tightness by changing the central distance between the motor output shaft 

and the milling drum central shaft. Proper belt tightness must be maintained. 5. Every 

time you change the cutter arrangement, check the cutter shaft and bushing. If a worn 

groove appears on the shaft, a new one is needed.